Pd 58%

Contacts on a base from the telephone blocks MKS.

Should be cut to fit the contact itself.

Pd 7%

Silver plated aluminum

The price depends on the palladium content.

Spectral analysis is carried out upon acceptance

Pd 1%

Pd 78%

Chemically pure palladium

The contacts of switches made of silver alloy on a copper base are non-magnetic.
The silver part must be about 50% of the total contact, otherwise a discount may apply

Silver alloy contacts of switches non-magnetic.
Tungsten-Silver Carbide (WCAg) contacts do not fit into this category.
If there is a large amount of solder residues, a discount may apply

Silver plated copper scrap.

The price of silver plated copper products depends on the thickness of the base.

Two-side, one-side

Gold plated watches and bracelets

The price depends on the thickness of the gold plating and equipment (with or without a mechanism)

Bracelets from watches with a hallmark are assessed as watches without a mechanism.

If the items show signs of severe wear, a discount may apply, and the discount is also applied to massive cases.

Produced in the USSR, the gilded watch cases are marked with two letters "Au", after the letters there were numbers: 5, 10, 20, 25, indicating the thickness of the gold coating in microns. For example: AU10, or Au-20. There are rare markings in the form of the inscription Au-12.5 or Au10 , sometimes instead of Au10 , the inscriptions AUX, or Au10 = were put.

There were only markings of the letters "Au", but in a frame in the form of a square or a rhombus, such stamps with a square and a rhombus denoted a gold plating 20 microns thick.

If the watch case has only the letters "Au", no numbers, then the coating will be 5 microns.

Watches and other gilded jewelry (cufflinks, brooches, rings, earrings, chains, pendants, etc.) without a brand are evaluated based on spectral analysis at the time of acceptance

Contacts of switches, relays made of silver alloy with the remnants of the holder, non-magnetic.
Holders must be cutted as close to the contact as possible, otherwise discounts may apply

Silver alloy contacts of switches non-magnetic.
If there is a large amount of solder residues, a discount may apply

Contacts of switches, relays made of silver alloy with the remnants of the holder magnetic.
Holders must be cutted as close to the contact as possible, otherwise discounts may apply

Contacts of switches, relays made of silver alloy on a copper base with remnants of the holder, non-magnetic.
Holders must be cutted as close to the contact as possible, otherwise discounts may apply

Scrap gold jewelry, dental crowns, electrical contacts, etc.
The price depends on the content of gold

Price depends on Pd content

Pd 1%

Pd 16%

Scrap silver jewelry, silverware, etc.

The price depends on the content of silver.

The silver content in unmarked items is determined by spectral analysis

The price of zinc-silver batteries depends on the brand and condition - new or used.
If you have not found the brand of your battery in the list - send us a request with a photo, we will tell you its price!

Pd 20%

Gold-plated contacts from connectors, freed from foreign material (plastic, wires, etc.)
The price of contacts depends on the thickness of the base - the thicker the base, the lower the gold content, respectively, the lower the price.
Also, contacts can be fully gold-plated or partially, which also affects the price.
Separate contacts by appearance before sending, this will allow us to quickly and accurately determine their price.
It is not recommended to disassemble connectors made in the USSR / RF - the gold content in these products is higher than in the others, but after disassembly it is not possible to identify them. Send connectors made in the USSR / RF unassembled!

Silver plated brass scrap

The price of silver-plated brass parts depends on the thickness of the brass base

Pd 28%

Contacts of switches made of silver alloy on a copper base are magnetic.
The silver part must be about 50% of the total contact, otherwise a discount may apply